Internal alterations in W10
W10 covers North Kensington. For internal alterations, the route depends on the exact property: conservation areas, Article 4 directions, listed status, tenure and the scheme details all change the answer. Use this district guide as local context, then run the address check before relying on permitted development or any consent assumption.
W10 mixes the Oxford Gardens conservation area, the Kensal Green cemetery setting and Portobello's northern reach. Conservation coverage is patchier than the south of the borough, but K&C's basement policy (CL7) and its property-specific Article 4 directions still apply — the address-level check decides the route.
First checks for internal alterations
Service-specific- A structural engineer's check on whether the wall is load-bearing
- Building-control approval and inspections for the opening
- Party wall notice if a beam bears into a neighbour's wall
District pages are not point-level checks. They do not confirm whether a specific property is listed, inside a conservation area, or subject to an Article 4 direction.
Local planning context · Kensington and Chelsea
Real · planning.data.gov.ukKensington and Chelsea has 39 conservation areas and 82 Article 4 areas in the official dataset. W10 is too broad to say which apply to your property; the address check tests the point against available geometry.
Read the borough-wide context on the Kensington and Chelsea planning guide.
What changes the route?
| Where constraints apply | No planning permission for internal changes (unless the property is listed) — but a structural engineer and building-control sign-off are needed. |
| Where no designation is found | No planning permission needed for internal changes — but you'll need a structural engineer and building control for any load-bearing wall. |
Approvals and who deals with them
| What you may need | Likelihood | Who usually deals with it |
|---|---|---|
| Planning permission Internal alterations to a house do not normally need planning permission (unless the property is listed, or the work changes the use). | Not usually | Planning consultant / architect |
| Building Regulations approval A structural opening (beam/lintel) needs building-control approval and inspection — for structure, fire and means of escape. | Required | Building control + your builder |
| Structural engineer's design Removing or notching a load-bearing wall needs beam calculations and a drawing before any quotes are reliable. | Required | Structural engineer |
| Party Wall etc. Act 1996 notice Cutting a beam bearing into a wall shared with a neighbour (a party wall) requires written notice and possibly a surveyor. | Possible | Party wall surveyor |
| Licence to Alter (if a leasehold flat) If the property is a leasehold flat, the freeholder's consent for structural alterations is usually required by the lease. | Possible | Chartered surveyor / freeholder / solicitor |
| Listed building consent We do NOT check listed status. If the property is listed, consent is needed for works affecting its character — confirm on the National Heritage List for England. | Verify | Heritage adviser / conservation officer |
Cost context
| Single structural opening (beam, calcs, building control, making good) | £3,500 – £9,000 |
| Through-room knock-through (two rooms into one) | £6,000 – £15,000 |
| Whole-floor reconfiguration | £20,000 – £60,000+ |
| Structural engineer + building-control fees (add) | £1,200 – £3,500 |
Indicative London ranges — confirm against a structural engineer's drawing.
Watch-outs in W10
- Assuming a wall is non-structural — walls carrying floor joists or above an opening often are; get it checked before pricing.
- Beam bearings landing on a party wall, pulling the job into the Party Wall Act.
- Services (soil pipes, rising mains, gas) buried in the wall to be removed, adding re-routing cost.
- A listed building, where internal changes affecting character need consent even though 'it's only internal'.
Next steps
- Commission a structural engineer to confirm whether the wall is load-bearing and design the opening.
- Submit a Building Regulations application (full plans or building notice) and arrange inspections.
- If a beam bears into a party wall, serve Party Wall notices before work starts.
- Get comparable quotes against the engineer's drawing, not a verbal scope.
Related guides
Two separate approval systems. Confusing them is the most common — and most expensive — mistake in domestic building.
Read the guide →Building regulations are a separate system from planning — and the certificate at the end is the one your buyer's solicitor will ask for.
Read the guide →Almost every London extension, loft and basement engages this Act. Here's how it actually works.
Read the guide →More services in W10
First check: Freeholder consent / Licence to Alter — read your lease's alterations clause
Service guide →First check: Whether it's permitted development or needs a planning application
Service guide →First check: Whether the dormer needs planning permission
Service guide →First check: Planning permission and the borough's basement policy
Service guide →First check: The intended use (office/gym vs sleeping) — it changes everything
Service guide →First check: The property's planning history and any enforcement
Service guide →First check: Whether the building is listed, and at what grade
Service guide →Planning Permission Checker provides planning and cost intelligence for early feasibility only. It is not legal, planning, valuation, architectural, structural, or surveying advice. All estimates are indicative and must be verified by qualified professionals before purchase, design, planning submission, or construction.
Cost estimates are indicative only — not a quotation. Final price depends on survey, specification, structure, access, party wall matters, VAT, professional fees, and contractor availability.
Planning outcomes are not guaranteed. Local planning authorities make final decisions.